Model railroad ballast is available for purchase in your local hobby shop or online in various sizes and colors. Choose the size and color appropriate for your scale, locale, and complement your scenery colors. Many real railroads use the rocks available in the local area as ballast. So it’s good to know what color ballast your prototypical railroad uses for their tracks in the area you are modeling. If you’re freelancing, this won’t matter much. You can pick whatever color of model railroad ballast that looks good with the rest of your scenery. If you don’t like any of the available colors, you can mix the different colors to get the shade you want.
Experiment with this first using a small amount of the ballast, e.g., 1 teaspoon of one color mixed with 1 teaspoon of another color, and see if the blend is what you are looking for. If so, then blend larger amounts in the same proportion to use on your layout. You may wish to vary the shade of model railroad ballast you use in different areas of your layout. For example, you may use a darker shade around freight yards. Engine servicing areas than you would on the mainline between towns. However, I wouldn’t use too many different shades or colors on the same layout—the technique for applying model railroad ballast. When you’re finished fixing your model railroad track to your sub roadbed and painting the rails and ties, you’re ready for ballasting.
Get real Model Railroad Ballast
There are different techniques for doing this. I have done it different ways, but I think the following method works the best… Use a small teaspoon to hold a small amount of dry ballast directly over the track. Gently tap the opposite edge of the spoon with your finger with the spoon tilted. So that the ballast sprinkles out of the spoon a little at a time. Work in small sections of track at first.
Sprinkle the ballast over the inside of the rails first, then over the outside of the rails. The outside edges of the ballast should be neat and straight. After you have sprinkled the ballast on a section of the track with the spoon, take a medium or soft brush to spread the ballast in and around the ties both inside the rails and out. Again, keeping the outside edges neat and straight. Ideally, none of the ballast should be on top of the rails, just in between them.
This isn’t easy to do with N or Z scale, but do the best you can. You can then proceed on to the next section and do the same. Avoid getting any ballast around the points or mechanisms of turnouts. If this happens, vacuum the ballast out of that area. After you’ve put down the ballast on a few feet of track. After you have groomed the ballast the best you can with a brush, then you’re ready to glue it down. Prepare a mixture of 1 part white glue (Elmer’s) to 4 parts water and 1 part alcohol (isopropyl). If you have previously painted your track ties. Test a small area of the painted track with alcohol to make sure the paint doesn’t dissolve and run all over the ballast.
If it does, then use a few drops of liquid detergent in your diluted glue rather than alcohol to make it “wetter” so it flows into the ballast and under the track well.) Use a pipette to draw up the glue mixture and then hold the tip of the pipette close to the track’s center between the rails. Gently drip the glue mixture onto the ballast and allow the glue to seep into the ballast slowly.
Continue to drip the glue in until you see the white glue saturating the ballast but not enough to cause pooling. The glue should seep and wick its way out from the center to the outside of the rails from underneath. You’ve added enough when you see the ballast on the outside of the rails become saturated with the white glue. You can then continue the same process along the next sections of the track.
If the ballast gets accidentally moved from where you placed it. Use the brush or your finger to move it back in place. Do not get the glue or ballast anywhere near the points or mechanism of your turnouts. Use a soft cloth or sponge on top of the rails to clean off any glue that may have landed there. Being careful not to disturb the ballast. Allow this to dry overnight. The white glue will no longer be visible, and the ballast should be firmly glued in place. Check your track carefully to ensure none of the model railroad ballast has been glued to the inside of the rails, which will cause a derailment. Also, check your turnouts to be sure they still work. Clean off any glue that may have dried on the insides or tops of the rails.